Hydroxylase-like Biomimetic Nanozyme Synthesized via a Urea-Mediated MOF Pyrolytic Reconstruction Strategy for Non-"o-Phenol hydroxyl"-Dependent Dopamine Electrochemical Sensing.

Dopamine (DA), an essential neurotransmitter, is closely associated with various neurological disorders, whose real-time dynamic monitoring is significant for evaluating the physiological activities of neurons. Electrochemical sensing methods are commonly used to determine DA, but they mostly rely on the redox reaction of its o-phenolic hydroxyl group, which makes it difficult to distinguish it from substances with this group. Here, we design a biomimetic nanozyme inspired by the coordination structure of the copper-based active site of dopamine ß-hydroxylase, which was successfully synthesized via a urea-mediated MOF pyrolysis reconstruction strategy. Experimental studies and theoretical calculations revealed that the nanozyme with Cu-N3 coordination could hydroxylate the carbon atom of the DA ß-site at a suitable potential and that the active sites of this Cu-N3 structure have the lowest binding energy for the DA ß-site. With this property, the new oxidation peak achieves the specific detection of DA rather than the traditional electrochemical signal of o-phenol hydroxyl redox, which would effectively differentiate it from neurotransmitters, such as norepinephrine and epinephrine. The sensor exhibited good monitoring capability in DA concentrations from 0.05 to 16.7 µM, and its limit of detection was 0.03 µM. Finally, the sensor enables the monitoring of DA released from living cells and can be used to quantitatively analyze the effect of polystyrene microplastics on the amount of DA released. The research provides a method for highly specific monitoring of DA and technical support for initial screening for neurocytotoxicity of pollutants.

Exploring the Complex Impact of Proteins on Dopamine Polymerization: Mechanisms and Strategies for Modulation.

Polydopamine (pDA) is a valuable material with wide-ranging potential applications. However, the complex and debated nature of dopamine polymerization complicates our understanding. Specifically, the impact of foreign substances, especially proteins, on pDA formation adds an additional layer of subtlety and complexity. This study delves into specific surface features of proteins that predominantly shape their impact on dopamine polymerization. Notably, the biotin-binding site emerges as a critical region responsible for the pronounced inhibitory effect of avidin and neutravidin on the dopamine polymerization process. The binding of biotin successfully mitigates these inhibitory effects. Moreover, several nucleases demonstrated a significant hindrance to pDA formation, with their impact substantially alleviated through the introduction of DNA. It is speculated that hydrogen bonding, electrostatic, cation-π, and/or hydrophobic interactions may underlie the binding between protein surfaces and diverse oligomeric intermediates formed by the oxidation products of dopamine. Additionally, we observed a noteworthy blocking effect on the dopamine polymerization reaction induced by erythropoietin (EPO), a glycoprotein hormone known for its role in stimulating red blood cell production and demonstrating neuroprotective effects. The inhibitory influence of EPO persisted even after deglycosylation. These findings not only advance our comprehension of the mechanisms underlying dopamine polymerization but also provide strategic insights for manipulating the reaction to tailor desired biomaterials.

Fluorometric "AND" logic gate for detection of tyramine and tyrosinase based on in-situ formation of silicon-containing nanoparticles.

BACKGROUND: Tyramine is an important index of food freshness degree, and tyrosinase that can specifically oxidized monophenolamine to catecholamine plays a crucial part in the occurrence and development of melanin-related skin diseases. Therefore, it is crucial to develop sensitive and efficient methods for the detection of tyramine and tyrosinase. RESULTS: In this work, encouraged by tyrosinase-triggered specific oxidation of tyramine to dopamine and the unique fluorescent reaction between dopamine and amino silane, we have developed a one-step synthetic strategy of silicon containing nanoparticles (Si CNPs) for "turn-on" detection of tyramine and tyrosinase. The Si CNPs formed with thoroughly studied mechanism exhibit uniform structure and robust yellow-green fluorescence. The low detection limits for tyramine (1.87 µM) and tyrosinase (0.0029 U/mL) demonstrate admirable sensitivity outstripping most methods. The proposed assay achieves satisfactory results in the determination of tyramine and tyrosinase activity in real samples. Furthermore, we leverage this new fluorescent assay to enable the fabrication of an "AND" Boolean logic gate. SIGNIFICANCE: The entire process can be completed at easily available temperature and pressure with rapid response, convenient operation and visual observation. This fluorescent assay featured with excellent sensitivity, selectivity and stability has considerable prospects in the application of biosensors and disease diagnosis.

Electrochemical Characterization of Neurotransmitters in a Single Submicron Droplet.

Single-entity electrochemistry, which employs electrolysis during the collision of single particles on ultramicroelectrodes, has witnessed significant advancements in recent years, enabling the observation and characterization of individual particles. Information on a single aqueous droplet (e.g., size) can also be studied based on the redox species contained therein. Dopamine, a redox-active neurotransmitter, is usually present in intracellular vesicles. Similarly, in the current study, the electrochemical properties of neurotransmitters in submicron droplets were investigated. Because dopamine oxidation is accompanied by proton transfer, unique electrochemical properties of dopamine were observed in the droplet. We also investigated the electrochemical properties of the adsorbed droplets containing DA and the detection of oxidized dopamine by the recollision phenomenon.

A Portable Electrochemical Dopamine Detector Using a Fish Scale-Derived Graphitized Carbon-Modified Screen-Printed Carbon Electrode.

In this paper, a highly conductive alkali-activated graphitized carbon (a-GC) was prepared using tilapia fish scales as precursors through enzymolysis, activation and pyrolytic carbonization methods. The prepared a-GC was modified on the surface of a screen-printed carbon electrode to construct a flexible portable electrochemical sensing platform, which was applied to the differential pulse voltametric detection of dopamine (DA) using a U-disk electrochemical workstation combined with a smart phone and Bluetooth. The prepared a-GC possesses good electrical conductivity, a large specific surface area and abundant active sites, which are beneficial for the electrooxidation of DA molecules and result in excellent sensitivity and high selectivity for DA analysis. Under the optimal conditions, the oxidation peak current of DA increased gradually, with its concentrations in the range from 1.0 µmol/L to 1000.0 µmol/L, with the detection limit as low as 0.25 µmol/L (3S/N). The proposed sensor was further applied to the determination of DA in human sweat samples, with satisfactory results, which provided an opportunity for developing noninvasive early diagnosis and nursing equipment.

A nature-inspired multifunctional adhesive for cartilage tissue-biomaterial integration.

Surgical adhesives play a crucial role in tissue integration and repair, yet their application in wet conditions has been severely limited by inadequate adhesive strength and subpar biocompatibility. Furthermore, tissue adhesives have rarely been reported in cartilage tissue repair. In this study, a three-armed dopamine-modified hyaluronic acid derivative adhesive was prepared to function as a bio-inspired adhesive in moist environments. To meet the clinical requirements for cartilage tissue adhesion, we studied its chemical structure, including microscopic morphology, adhesion properties with materials and tissues, in vivo degradation rules, and biological evaluation. The OGMHA8-DOPA adhesive with the optimal aldehyde substitution degree and dopamine-grafting rate was determined by analyzing the experimental conditions. SEM results revealed that the cartilage tissue adhered to a porous interconnected structure. The excellent biocompatibility of the material not only facilitated chondrocyte adhesion but also supported their proliferation on its surface. Animal experiments have demonstrated that this material has no observable inflammatory response or incidence of fibrous capsule formation. The degradation timeline of the material extends beyond the duration of two weeks. The dopamine-modified adhesive exhibited a tight interfacial binding force between the biomaterial and cartilage tissue and excellent biocompatibility in watery tissue, revealing its potential for application in cartilage tissue repair and minimally invasive surgery.

In situ monitoring of cytoplasmic dopamine levels by noble metals decorated carbon fiber tips.

Dopamine (DA), a catecholamine neurotransmitter, is crucial in brain signal transmission. Monitoring cytoplasmic DA levels can reflect changes in metabolic factors and provide valuable information for researching the mechanisms involved in neurodegenerative diseases. However, the in-situ detection of intracellular DA is constrained by its low contents in small-sized single cells. In this work, we report that noble metal (Au, Pt)-modified carbon fiber micro-nanoelectrodes are capable of real-time detection of DA in single cells with excellent sensitivity, selectivity, and anti-contamination capabilities. Notably, noble metals can be modified on the electrode surface through electrochemical deposition to enhance the conductivity of the electrode and the oxidation current of DA by 50 %. The nanosensors can work stably and continuously in rat adrenal pheochromocytoma cells (PC12) to monitor changes in DA levels upon K+ stimulation. The functionalized carbon fibers based nanosensors will provide excellent prospects for DA analysis in the brains of living animals.

A disposable sensor based on one-pot synthesized tungsten oxide nanostructure-modified screen printed electrodes for selective detection of dopamine and uric acid.

Here, screen-printed carbon electrodes (SPCEs) were modified with ultrafine and mainly mono-disperse sea urchin-like tungsten oxide (SUWO3) nanostructures synthesized by a simple one-pot hydrothermal method for non-enzymatic detection of dopamine (DA) and uric acid (UA) in synthetic urine. Sea urchin-like nanostructures were clearly observed in scanning electron microscope images and WO3 composition was confirmed with XRD, Raman, FTIR and UV-Vis spectrophotometer. Modification of SPCEs with SUWO3 nanostructures via the drop-casting method clearly reduced the Rct value of the electrodes, lowered the ∆Ep and enhanced the DA oxidation current due to high electrocatalytic activity. As a result, SUWO3/SPCEs enabled highly sensitive non-enzymatic detection of DA (LOD: 51.4 nM and sensitivity: 127 µA mM-1 cm-2) and UA (LOD: 253 nM and sensitivity: 55.9 µA mM-1 cm-2) at low concentration. Lastly, SUWO3/SPCEs were tested with synthetic urine, in which acceptable recoveries for both molecules (94.02-105.8%) were obtained. Given the high selectivity, the sensor has the potential to be used for highly sensitive simultaneous detection of DA and UA in real biological samples.

Electrodeposited reduced graphene oxide-PEDOT:PSS/Nafion hybrid interface for the simultaneous determination of dopamine and serotonin.

The electrochemically deposited reduced graphene oxide-PEDOT:PSS/Nafion (rGO-PP/NF) hybrid material has provided a favorable interface for the simultaneous detection of dopamine (DA) and serotonin (5-HT). The rGO-PP/NF onto the Au seed layer of the flexible substrate was simple, and it was followed by the sequential electrophoretic deposition of GO, reduction at the optimal pH buffer media, electropolymerization of EDOT:PSS, and Nafion coating. The strong electron-transport capacity between rGO-PEDOT:PSS and the negatively charged Nafion matrix might allow the highly sensitive, simultaneous, and selective detection of DA and 5-HT due to its high affinity for cations. In the results of the electrochemical response, well-separated oxidation peaks were observed in a mixture that contained various concentrations of DA and 5-HT. It showed the dynamic sensing of DA and 5-HT in the ranges of 0.5-75 µM and 0.05-50 µM, respectively, and the detection limits of 0.17 and 0.16 µM, respectively. In the mixture of DA and 5-HT, the sensor had a detection limit of 0.1 µM for 5-HT and DA, and its sensitivities of DA and 5-HT were 99.3 and 86 µA/µMcm2. Furthermore, it demonstrated high selectivity, reproducibility, stability, and a recovery property in the human serum spike test that was good enough for the practical use.

In-situ integrated electrodes of FeM-MIL-88/CP for simultaneous ultra-sensitive detection of dopamine and acetaminophen based on crystal engineering strategy.

Designing and exploiting integrated electrodes is the current inevitable trend to realize the sustainable development of electrochemical sensors. In this work, a series of integrated electrodes prepared by in situ growing the second metal ion-modulated FeM-MIL-88 (M = Mn, Co and Ni) on carbon paper (CP) (FeM-MIL-88/CP) were constructed as the electrochemical sensing platforms for the simultaneous detection of dopamine (DA) and acetaminophen (AC). Among them, FeMn-MIL-88/CP exhibited the best sensing behaviors and achieved the trace detection for DA and AC owing to synergistic catalysis between Fe3+, Mn2+ and CP. The electrochemical sensor based on FeMn-MIL-88/CP showed ultra-high sensitivities of 2.85 and 7.46 µA µM-1 cm-2 and extremely low detection limits of 0.082 and 0.015 µM for DA and AC, respectively. The FeMn-MIL-88/CP also exhibited outstanding anti-interference ability, repeatability and stability, and satisfactory results were also obtained in the detection of actual samples. The mechanism of Mn2+ modulation on the electrocatalytic activity of FeMn-MIL-88/CP towards DA and AC was revealed for the first time through the density functional theory (DFT) calculations. Good adsorption energy and rapid electron transfer worked synergistically to improve the sensing performances of DA and AC. This work not only provided a high-performance integrated electrode for the sensing field, but also demonstrated the influencing factors of electrochemical sensing at the molecular levels, laying a theoretical foundation for the sustainable development of subsequent electrochemical sensing.

Simultaneous recognition of dopamine and uric acid in real samples through highly sensitive new electrode fabricated using ZnO/carbon quantum dots: bio-imaging and theoretical studies.

Dopamine (DA) and uric acid (UA), which are vital components in human metabolism, cause several health problems if they are present in altered concentrations; thus, the determination of DA and UA is essential in real samples using selective sensors. In the present study, graphite carbon paste electrodes (CPE) were fabricated using ZnO/carbon quantum dots (ZnO/CQDs) and employed as electrochemical sensors for the detection of DA and UA. These electrodes were fully characterized via different analytical techniques (XRD, SEM, TEM, XPS, and EDS). The electrochemical responses from the modified electrodes were evaluated using cyclic voltammetry, square wave voltammetry, and electrochemical impedance spectroscopy. The results showed that the present electrode has exhibited high sensitivity towards DA, recognizing even at low concentrations (0.12 µM), and no inference was observed in the presence of UA. The ZnO/CQD electrode was applied for the simultaneous detection of co-existing DA and UA in real human urine samples and the peak potential separation between DA and UA was found to be greatly associated with the synergistic effect originated from ZnO and CQDs. The limit of detection (LOD) of the electrode was analyzed, and compared with other commercially available electrodes. Thus, the ZnO/CQD electrode was used to detect DA and UA in real samples, such as Saccharomyces cerevisiae cells.

Real-time selective detection of dopamine and serotonin at nanomolar concentration from complex in vitro systems.

Electrochemical sensors provide means for real-time monitoring of neurotransmitter release events, which is a relatively easy process in simple electrolytes. However, this does not apply to in vitro environments. In cell culture media, competitively adsorbing molecules are present at concentrations up to 350 000-fold excess compared to the neurotransmitter-of-interest. Because detection of dopamine and serotonin requires direct adsorption of the analyte to electrode surface, a significant loss of sensitivity occurs when recording is performed in the in vitro environment. Despite these challenges, our single-walled carbon nanotube (SWCNT) sensor was capable of selectively measuring dopamine and serotonin from cell culture medium at nanomolar concentration in real-time. A primary midbrain culture was used to prove excellent biocompatibility of our SWCNT electrodes, which is a necessity for brain-on-a-chip models. Most importantly, our sensor was able to electrochemically record spontaneous transient activity from dopaminergic cell culture without altering the culture conditions, which has not been possible earlier. Drug discovery and development requires high-throughput screening of in vitro models, being hindered by the challenges in non-invasive characterization of complex neuronal models such as organoids. Our neurotransmitter sensors could be used for real-time monitoring of complex neuronal models, providing an alternative tool for their characterization non-invasively.

Preparation and Hemostatic Effect of Micro-Nanograded Porous Particles Doped with Dopamine-Based Water-Triggered Intelligent Composite Adhesives.

The wet environment of water or tissue in bleeding wounds poses significant challenges to the adhesion performance of existing hemostatic adhesives. An intelligent composite adhesive prepared by doping starch-based silicate micro-nanograded porous particles (MBC@CMS) with dopamine-hyperbranched polymers (HPD, 7800 Mw) synthesized by the Michael addition reaction could be triggered by water to form a glue (MBC@CMS-HPD). The results indicated that MBC@CMS-HPD could still have adhesion properties under running water washing and water immersion and could effectively seal the water outlet. The results of the glue-forming mechanism showed that MBC@CMS-HPD had better wettability than water, which could eliminate water molecules at the wet adhesive surface. When contacted with water, the agglomeration of the HPD hydrophobic chain increases the exposure of the catechol group, and the relative atomic mass of the N element on the surface increases from 2.8 to 4.8%. The adhesion of MBC@CMS-HPD was enhanced and stable. MBC@CMS-HPD showed significant hemostasis effects in five injury bleeding models of Sprague-Dawley (SD) rats and New Zealand rabbits. Especially in the fatal femoral artery bleeding model of New Zealand rabbits, MBC@CMS-HPD reduced the amount of bleeding by 75% and shortened the bleeding time by 78% compared with the a-cyanoacrylate adhesives. The results of the coagulation mechanism showed that compared with HPD, MBC@CMS-HPD could activate both endogenous and exogenous coagulation pathways. Among them, after contact with blood, HPD formed a gel to close the blood outlet, and MBC@CMS entered the wound to activate the internal and external coagulation pathways. In addition, HPD and MBC@CMS had good histocompatibility and degradability, which has the potential to be applied to different wounds.

Tough and On-Demand Detachable Wet Tissue Adhesive Hydrogel Made from Catechol Derivatives with a Long Aliphatic Side Chain.

Wet adhesion is critical in cases of wound closure, but it is usually deterred by the hydration layer on tissues. Inspired by dopamine-mediated underwater adhesion in mussel foot proteins, wet tissue adhesives containing catechol with 2-3 carbons side chains are reported mostly. To make wet adhesion of this type of adhesives much tougher, catechol derivatives with a long aliphatic side chain (≈10 atoms length) are synthesized. Then, a series of strong wet tissue adhesive hydrogels are prepared through photoinduced copolymerization of acrylic acid with synthetic monomers. The adhesive hydrogel has a high cohesion strength, that is, tensile strength and strain, and toughness of ≈1800 kPa, ≈540%, and ≈4100 kJ m-3 , respectively. Its interfacial toughness on wet and underwater porcine skin is respectively ≈1300 and ≈1100 J m-2 , and its adhesion strength to wet porcine skin is ≈153 kPa. These values are much higher than those of dopamine-based adhesives in the same conditions, demonstrating that the long aliphatic side chain on catechol can greatly improve the wet tissue-adhesion. Additionally, the tough interfacial adhesion can be broken on demand with 5 wt.% aqueous urea solution. This adhesive hydrogel is highly promising in safe wound closure.

Mechanically tunable, antibacterial and bioactive mussel adhesive protein/hyaluronic acid coacervates as bioadhesives.

In this work a bioadhesive was developed based on coacervates composed of recombinant mussel adhesive protein (MAP) and dopamine grafted hyaluronic acid (HA). Dopamine profoundly affected rheological attributes of the coacervates, leading to reduced rigidity, enhanced chain flexibility, more sol-like and fluid character and higher tolerance against structural collapse. The coacervates were rendered flowability, injectability, and adaptability, benefiting convenient delivery and making good contact with the skin to provide firm sealing for wounds of various shape and depth. It is the first time reported that MAP/HA coacervates are inherently antibacterial with 100 % growth inhibition against Gram-positive bacteria Staphylococcus aureus and Gram-negative bacteria Escherichia coli. The antibacterial capability was disclosed to be positively related to catechol content. To further enhance the coacervates bioactivity, a small bioactive peptide thymosin was added and was revealed to promote fibroblasts migration. The coacervates hold great potential as practical bioadhesives both from the perspective of rheological properties and biological activities.

Ultralight 3D Graphene Oxide Aerogel Decorated with Pd-Fe Nanoparticles for the Simultaneous Detection of Eight Biomolecules.

In this proof-of-concept study, an ultralight graphene oxide aerogel (GOx-Aero) decorated with bimetallic palladium-iron nanoparticles (Pd-Fe) was synthesized and immobilized on a glassy carbon electrode (GCE) for electrochemical sensor applications. The main objective of this work was to develop a sensitive electrochemical sensor capable of simultaneously detecting eight biomolecules, including ascorbic acid (AA), dopamine (DA), uric acid (UA), 8-hydroxyguanine (8HG), guanine (G), adenine (A), thymine (T), and cytosine (C). To the best of our knowledge, this is the first time that an electrochemical sensor has been able to detect eight biomolecules simultaneously. The bimetallic GOx aerogel significantly enhanced the performance of the sensor by increasing the electroactive area, conductivity, and anodic peak current response. The sensor demonstrated sharp, well-defined, and continuous oxidation peaks for all eight analytes of interest and wide linear ranges of 5.0-1750, 0.25-100.0, 0.5-500.0, 0.5-375.0, 0.5-500.0, 0.5-500.0, 5.0-1500.0, and 5.0-1500.0 µM for AA, DA, UA, 8HG, G, A, T, and C, respectively. The prepared sensor also exhibited excellent stability, reproducibility, and sensitivity with a very low limit of detection (LOD) of 553.7, 1.8, 69.6, 43.2, 42.9, 72.3, 57.2, and 318.4 nM for AA, DA, UA, 8HG, G, A, T, and C, respectively. The Pd-Fe-GOx-Aero-GCE was also tested in various real samples such as artificial saliva, artificial cerebrospinal fluid (CSF), salmon sperm DNA, and genomic DNA from calf thymus, where it demonstrated good recovery values. Additionally, the novel developed sensor was used to monitor the interaction between the anticancer drug, cisplatin, which has well-described binding affinity with the G and A bases in DNA. Overall, Pd-Fe-GOx-Aero-GCE displayed an extremely promising platform not only for the simultaneous detection of eight biomolecules in complex biological matrices but also for DNA-drug interaction studies toward the development of electrochemical high-throughput drug screening assays, which is of great importance in the field.

A Novel Polyurethane-Based Polyion Complex Material with Tunable Selectivity against Interferents for Selective Dopamine Determination.

Polyion complex (PIC) materials have been widely used in biosensors due to their molecular selectivity. However, achieving both widely controllable molecular selectivity and long-term solution stability with traditional PIC materials has been challenging due to the different molecular structures of polycations (poly-C) and polyanions (poly-A). To address this issue, we propose a novel polyurethane (PU)-based PIC material in which the main chains of both poly-A and poly-C are composed of PU structures. In this study, we electrochemically detect dopamine (DA) as the analyte and L-ascorbic acid (AA) and uric acid (UA) as the interferents to evaluate the selective property of our material. The results show that AA and UA are significantly eliminated, while DA can be detected with a high sensitivity and selectivity. Moreover, we successfully tune the sensitivity and selectivity by changing the poly-A and poly-C ratios and adding nonionic polyurethane. These excellent results were employed in the development of a highly selective DA biosensor with a detection range from 500 nM to 100 µM and a 3.4 µM detection limit. Overall, our novel PIC-modified electrode has the potential to advance biosensing technologies for molecular detection.

Electrochemical Sensing of Dopamine Using Polypyrrole/Molybdenum Oxide Bilayer-Modified ITO Electrode.

The electrochemical sensing of biomarkers has attracted more and more attention due to the advantages of electrochemical biosensors, including their ease of use, excellent accuracy, and small analyte volumes. Thus, the electrochemical sensing of biomarkers has a potential application in early disease diagnosis diagnosis. Dopamine neurotransmitters have a vital role in the transmission of nerve impulses. Here, the fabrication of a polypyrrole/molybdenum dioxide nanoparticle (MoO3 NP)-modified ITO electrode based on a hydrothermal technique followed by electrochemical polymerization is reported. Several techniques were used to investigate the developed electrode's structure, morphology, and physical characteristics, including SEM, FTIR, EDX, N2 adsorption, and Raman spectroscopy. The results imply the formation of tiny MoO3 NPs with an average diameter of 29.01 nm. The developed electrode was used to determine low concentrations of dopamine neurotransmitters based on cyclic voltammetry and square wave voltammetry techniques. Furthermore, the developed electrode was used for monitoring dopamine in a human serum sample. The LOD for detecting dopamine by using MoO3 NPs/ITO electrodes based on the SWV technique was around 2.2 nmol L-1.

Effects of olanzapine and lithium carbonate antipsychotic agents on dopamine oxidation.

Olanzapine (OLZ) and lithium carbonate (Li2CO3) are the main drugs for treating mental disorders related to dopamine (DA). A highly conductive carbon paper sensing electrode is used to investigate the effects of OLZ and Li2CO3 on DA oxidation due to its amplification of oxidation peak currents. Different chemical properties of drugs have different effects on DA oxidation. The presence of OLZ fouling on the electrode surface due to the irreversible adsorption weakens the sensing activity and thus reduces the DA oxidation peak current. However, the fixed DA oxidation peak potential at 0.22 V indicates no interaction between them. The hydrolysis effect of Li2CO3 increases the solution pH from 7.47 to 9.73, which promotes the deprotonation of DA, leading to a 156 mV negative shift of the DA oxidation peak potential. Additionally, a 94% decrease of the DA peak current may be related to the generation of polydopamine in alkaline media.

Holey MoS2-based electrochemical sensors for simultaneous dopamine and uric acid detection.

In this study, two-dimensional holey MoS2 (h-MoS2) nanosheets were used to develop electrochemical sensors for simultaneous detection of dopamine (DA) and uric acid (UA). The holes were created on MoS2 layers using hydrogen peroxide (H2O2) in the presence of Bovine Serum Albumin (BSA). h-MoS2 was characterized by transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Raman spectroscopy, dynamic light scattering (DLS), and ultraviolet-visible spectroscopy (UV-vis). Electrochemical dopamine and uric acid sensors were prepared by drop-casting h-MoS2 on a glassy carbon electrode (GCE). The electroanalytical performance of the sensors was evaluated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS) methods. The sensors revealed linear ranges between 50-1200 µM and 200-7000 µM with a limit of detection (LOD) of 4.18 µM and 5.62 µM for DA and UA, respectively. Furthermore, the h-MoS2-based electrochemical sensors showed high stability, sensitivity, and selectivity. The reliability of the sensors was elucidated in human serum. Recoveries ranging between 100.35% and 102.48% were calculated from real sample experiments.